Language · English

TECHNOLOGY & MODEL SELECTION

Solid-State and Semi-Solid UAV Batteries Compared

Separate the technology description from the specification of the pack you will install. Use model-level evidence to decide what belongs on your shortlist.

Explore the guide
8S 40000mAh Solid-State UAV Battery
8S 40000mAh Solid-State UAV Battery

What the terms tell you

Solid-state battery terminology refers to the use of solid electrolyte materials; an all-solid-state design is distinct from a design retaining a liquid electrolyte component. Semi-solid-state commonly describes a solid–liquid hybrid approach, so the supplier’s model documentation is needed to establish the particular construction.

This general distinction does not establish the electrolyte formulation of an individual New Journey model. Do not infer that a product labelled solid-state has a particular all-solid-state construction without its supporting documentation.

For selection, keep the exact model designation attached to the specification. The technology name itself does not guarantee longer flight time. Voltage compatibility, finished dimensions, mass, charging conditions and the approved discharge limits remain separate decisions.

Compare these as different packs

New Journey lists the following finished packs separately. Their capacities are comparable as charge quantities, but their series counts and nominal voltages differ. This is a specification comparison, not a controlled test of one technology against the other.

8S 40000mAh Solid-State UAV Battery

8S 40000mAh Solid-State UAV Battery

Series configuration
8S
Capacity
40000mAh / 40Ah
Nominal voltage
29.6V
Nominal energy
1184Wh; calculated from 29.6V x 40Ah
Charge ceiling
34.0V
Body dimensions
93 x 90 x 205mm; each dimension +/-5mm
Pack mass
3200g; approximate finished pack weight
6S 40000mAh Semi-Solid UAV Battery

6S 40000mAh Semi-Solid UAV Battery

Series configuration
6S1P; six 40Ah cells
Capacity
40Ah
Nominal voltage
22.2V
Nominal energy
888Wh; calculated from nominal voltage and rated capacity
Charge ceiling
25.5V
Body dimensions
210 x 92 x 62mm; maximum body size, L x W x T
Pack mass
2590g; reference pack mass

The first pack cannot replace the second simply because both are described as 40Ah. Each needs an aircraft and charging arrangement that accepts its voltage range. The dimensions also describe different shapes, so check cable routing and mounting rather than comparing volume alone.

The solid-state model lists 80.0A (2C) continuous discharge and 280A (7C) maximum discharge. The semi-solid model lists 200A (5C) as a source maximum continuous discharge figure, with the complete assembly limit still to be approved. Those qualifications are part of the specification: they are not interchangeable current ratings or evidence that one technology is universally better.

Discuss the voltage, load and installation limits of your aircraft before choosing between these configurations.

When the technology comparison is useful

Consider these options when you have a defined mass or installation constraint and need to assess specific alternative models. Request the current model documentation, then compare the complete assembly under the same application requirements. Include charge limits and connector arrangements in that discussion.

If your electrical system or battery bay has not been defined, begin with How to Select a UAV Battery Pack and the wider UAV battery range. A conventional UAV pack with the right voltage, current path and physical fit may be the relevant starting point. The conventional 12S product name alone provides no basis for calling it solid-state.

Keep cell figures separate from pack figures

The solid-state pack’s specification labels 400Wh/kg as individual cell energy density. It must not be presented as the energy density of the finished pack. Interconnections, leads, insulation, wrapping and any other assembly components belong to the finished mass and configuration.

The 3.6V 67Ah Solid State Battery Cell is an individual pouch cell for pack development. It is not a ready-to-install alternative to either finished pack in the comparison, nor does that link establish that this cell is used inside either model. The cells versus packs guide explains what remains to be specified at assembly level.

Move from a label to a configuration

Use the Solid-State UAV Batteries hub to find the relevant product pages, then check each model’s full specification. Bring the model URL, accepted voltage window, continuous load, available space and maximum installed mass to your enquiry. Ask New Journey about a suitable pack configuration without assuming that a technology name alone determines the result.

TALK TO NEW JOURNEY

Bring your application into focus.

Share the voltage, load, drawing and quantity for a configuration discussion.

Discuss your requirements